美国ASCO阿斯卡S290气控阀系列参数如下:
压力操作,不锈钢阀体,管夹或对焊接口,DN10-65MM,介质温度:-10℃~+184℃,操作压差:0-16公斤
• Water Treatment
• Pharmaceutical
• Petrochemical
• Food & Beverage
• Reliable and Robust Proportional Control
• Proportional flow control via 4-20mA signal (open loop)
• Closed loop control via external process signal
• Fail closed construction: valve closes upon loss of power
• IP66 enclosure allows valve to be used outdoors
• LED indicators for valve status and diagnostic functions
• Position feedback signal for optimal flow control
• Manual opening and closing function simplifies start up without controller system
• High flow rate due to angled seat design
• Handles viscous fluids up to 2700 SSU
• Energy Saving
• No air consumption when set point position is reached
• Low power consumption (3.6 W) when set point position is reached
• PositionerD is factory adjusted and tested saving installation time and cost
• Easy Calibration
• Initial regulation parameters can be modified on computer with downloadable APC software
and ASCO RS232 converter cable
Specifications
Series Open Close Fluids Steam Min. Max.
Pipe
Sizes
(in)
Operator
Size
(mm)
Max.
Fluid
Temp.
˚F (C˚)
Body
Material
Response
Time (sec.)
Operating Pressure
Differential (psi)
Pilot
Pressure (psi)
290 with PositionerD
2-Way, Normally Closed
(Suffix PDB67) ¨
90 1" - 2"
1/2" - 3/4"
1" - 2"
1.0
2.0 2.0
2.0 2.5
1.0
63
0 - 150 Bronze or
Stainless Steel 0 - 230 366 60 116
¨�Accuracy < 2%; Hysteresis < 2%; Repeatability < 1%; Linearity < 5%
美国ASCO JOUCOMATIC公司是世界500强之一的美国艾默生集团成员,是一家主要生产和销售流体控制阀以及气动控制元件的跨国公司,具有100多年的生产技术经验,在拥有超过30家工厂,为客户提供超过23,000的流体控制产品。ASCO旗下拥有众多品牌:等都是ASCO的成员,其中ASCO/RED HAT,SIRAI品牌包括通用型产品及部分适用于特殊工矿的产品,可控制普通介质。GENERAL CONTROL为燃烧系列阀,介质可为燃油等。SCIENTIFIC是微型阀适用于医疗器械及其他分析产品行业。JOUCOMATIC是专业的气动控制产品的品牌,而TRI-POINT为压力温度开关产品。
版权与免责声明:凡本网注明“来源:亚洲制造网”的所有作品,均为浙江兴旺宝明通网络有限公司-亚洲制造网合法拥有版权或有权使用的作品,未经本网授权不得转载、摘编或利用其它方式使用上述作品。已经本网授权使用作品的,应在授权范围内使用,并注明“来源:亚洲制造网”。违反上述声明者,本网将追究其相关法律责任。 本网转载并注明自其它来源(非亚洲制造网)的作品,目的在于传递更多信息,并不代表本网赞同其观点或和对其真实性负责,不承担此类作品侵权行为的直接责任及连带责任。其他媒体、网站或个人从本网转载时,必须保留本网注明的作品第一来源,并自负版权等法律责任。 如涉及作品内容、版权等问题,请在作品发表之日起一周内与本网联系,否则视为放弃相关权利。
展开全部